C80 and FXT20 Planning for 28 mm Stainless Tube Welding
28 mm stainless tube with 2-3 mm wall thickness is a small-to-mid tube welding case where head range should be checked carefully before final configuration. A United States buyer evaluated an FXT20 power source, C80 weld head, tungsten grinding support, and optional larger C-series heads for a 3/4-inch stainless tube application. FYID-Feiyide treated the case as a closed-head orbital welding selection because the immediate tube size is compact, while the requested equipment list also suggests future diameter expansion.
Is C80 the Right Head for 28 mm Stainless Tube?
C80 can work, but the future tube map matters
A 28 mm tube may fit within the lower part of a C80 workflow if the correct collets are available. However, for a single compact tube size, a smaller C-series head may sometimes be easier to handle. The reason to choose C80 is usually future coverage, not only the current 28 mm joint.
A FYID-Feiyide tube welder should be selected from the real tube map. If the buyer only welds 28 mm tube, the head choice should prioritize access and clamp fit. If the buyer expects larger tube sizes later, C80 becomes more logical as a range-protection decision.
2-3 mm wall thickness changes heat input
A 2-3 mm wall is not extremely thin, but it still needs stable heat input and repeatable slope timing. FXT20 controls the weld current profile and stores validated settings for future use. The tungsten grinder supports stable ignition and repeatable bead shape.
A FYID-Feiyide stainless steel tube welding machine depends on tube preparation as much as power control. Square tube ends, clean stainless surfaces, correct collets, and stable purge should be verified before sample welding.
How Should Optional C120 and C170 Be Considered?
Larger heads are for future diameter coverage
C120 and C170 should not be selected for the current 28 mm tube unless the buyer has a future tube list that requires larger OD coverage. Larger heads need more space around the joint and may be less convenient for compact tube work.
If the buyer expects a range of stainless tube sizes, the best approach is to divide them into diameter groups. C80 can cover one group, while C120 or C170 may cover larger groups. FXT20 can serve as the shared control platform if each head and tube group is validated separately.
Head-selection table for the 28 mm case
| Work condition | C80 relevance | C120/C170 relevance | FXT20 role | Buyer check |
|---|---|---|---|---|
| Current 28 mm tube | Possible with correct collets | Usually unnecessary | Stores program | Confirm actual OD |
| 2-3 mm wall | Needs stable heat input | Same procedure concern | Controls current timing | Validate sample weld |
| Future larger tube | May be limited | May become useful | Stores separate programs | Build tube map |
| Tight access | Check head size | More clearance needed | No mechanical effect | Measure joint area |
| Stainless quality | Purge and prep critical | Purge and prep critical | Repeats settings | Define inspection level |
What Results Are Realistic?
Repeatability after a validated sample weld
The expected result is a repeatable welding cycle for matching 28 mm stainless joints after the sample weld is accepted. FXT20 can repeat current timing and slope behavior, while the C-series head repeats the electrode path. The process still depends on fit-up, purge, tungsten condition, and inspection criteria.
A FYID-Feiyide food-grade orbital welding system can support 304L or 316L stainless tube after procedure validation. If the tube is used in process service, internal bead quality and purge discipline should be part of the acceptance plan.
Delivery route should not change technical selection
The delivery destination or forwarding route may affect logistics, but it should not determine the weld head. The correct technical sequence is tube data, head range, collet list, power compatibility, sample weld validation, and then production planning.
FYID-Feiyide's orbital welding solution for this United States inquiry should be framed as a compact stainless tube setup with future range options, not as a one-size-fits-all package.
Frequently Asked Questions
Q: Is C80 suitable for 28 mm stainless tube? A: C80 can be considered if correct collets are available, but access and future tube range should guide the final decision.
Q: Why consider C120 or C170? A: Those heads are useful only if the buyer expects larger tube sizes beyond the current 28 mm requirement.
Q: What does FXT20 control? A: FXT20 controls current timing, slope behavior, and stored weld programs for validated tube groups.
Q: Why include a tungsten grinder? A: Consistent tungsten geometry improves arc ignition and bead repeatability.
Q: What should be confirmed first? A: Actual OD, wall thickness, collets, material grade, purge setup, power compatibility, and inspection requirement.
https://www.fyid-feiyide.com